Progress and major BARRIERS of nanocatalyst development in direct methanol fuel cell: A review

Direct methanol fuel cells (DMFC), among the most suited and prospective alternatives for portable electronics, have lately been treated with nanotechnology. DMFCs may be able to remedy the energy security issue by having low operating temperatures, high conversion efficiencies, and minimal emission levels. Though, slow reaction kinetics are a significant restriction of DMFC, lowering efficiency and energy output. Nowadays, research is more focused on fundamental studies that are studying the factors that can improve the capacity and activity of catalysts. In DMFC, among the most widely explored catalysts are platinum and ruthenium which are enhanced in nature by the presence of supporting materials such as nanocarbons and metal oxides. As a result, this research sheds light on nanocatalyst development for DMFCs based on Platinum noble metal. To summarize, this research focuses on the structure of nanocatalysts, as well as support materials for nanocatalysts that can be 3D, 2D, 1D, or 0D. The support material described is made up of CNT, CNF, and CNW, which are the most extensively used because they improve the performance of catalysts in DMFCs. In addition, cost estimations for fuel cell technology are emphasized to show the technology's status and requirements. Finally, challenges to nanocatalyst development have been recognized, as well as future prospects, as recommendations for more innovative future research.     

Investigation of La0.6Sr0.4Co1-xNixO3-δ (x=0, 0.2, 0.4, 0.6, 0.8) catalysts on solid oxide fuel cells anode for biogas dry reforming

The introduction of catalyst on anode of solid oxide fuel cell (SOFC) has been an effective way to alleviate the carbon deposition when utilizing biogas as the fuel. A series of La_0.6Sr_0.4Co_1-xNi_xO_3-δ (x = 0, 0.2, 0.4, 0.6, 0.8) oxides are synthesized by sol-gel method and used as catalysts precursors for biogas dry reforming. The phase structure of La_0.6Sr_0.4Co_1-xNi_xO_3-δ oxides before and after reduction are characterized by X-ray diffraction (XRD). The texture properties, carbon deposition, CH₄ and CO₂ conversion rate of La_0.6Sr_0.4Co_1-xNi_xO_3-δ catalysts are evaluated and compared. The peak power density of 739 mW cm^?2 is obtained by a commercial SOFC with La_0.6Sr_0.4Co_0.4Ni_0.6O_3-δ catalyst at 850 °C when using a mixture of CH₄: CO₂ = 2:1 as fuel. This shows a great improvement from the cell without catalyst for internal dry reforming, which is attributed to the formation of NiCo alloy active species after reduction in H₂ atmosphere. The results indicate the benefits of inhibiting the carbon deposition on Ni-based anode through introducing the La_0.6Sr_0.4Co_0.4Ni_0.6O_3-δ catalyst precursor. Additionally, the dry reforming technology will also help to convert part of the exhaust heat into chemical energy and improve the efficiency of SOFC system with biogas fuel.     

The formed surface characteristics of SiCf/SiC composite in the nanosecond pulsed laser ablation

For the advantages of high-temperature resistance, corrosion resistance and ultra-high hardness, SiC_f/SiC composite is becoming a preferred material for manufacturing aero-engine parts. However, the anisotropy and heterogeneity bring great challenges to the processing technology. In this study, a nanosecond pulsed laser is applied to process SiC_f/SiC composite, where the influence of the scanning speed and laser scanning direction to the SiC fibers on the morphology of ablated grooves is investigated. The surface characteristics after ablation and the involved chemical reaction of SiC_f/SiC are explored. The results show that the increased laser scanning speed, accompanied by the decreasing spot overlap rate, leads to the less accumulation of energy on the material surface, so the ablation effect drops. In addition, for the anisotropy of the SiC_f/SiC material, the obtained surface characteristics are closely dependent on the laser scanning direction to the SiC fibers, resulting in different groove morphology. The element composition and phase analysis of the machined surface indicate that the main deposited product is SiO₂ and the carbon substance. The results can provide preliminary technical support for controlling the machining quality of ceramic matrix composites.     

Performance assessment of a direct steam solar power plant with hydrogen energy storage: An exergoeconomic study

Power generation and its storage using solar energy and hydrogen energy systems is a promising approach to overcome serious challenges associated with fossil fuel-based power plants. In this study, an exergoeconomic model is developed to analyze a direct steam solar tower-hydrogen gas turbine power plant under different operating conditions. An on-grid solar power plant integrated with a hydrogen storage system composed of an electrolyser, hydrogen gas turbine and fuel cell is considered. When solar energy is not available, electrical power is generated by the gas turbine and the fuel cell utilizing the hydrogen produced by the electrolyser. The effects of different working parameters on the cycle performance during charging and discharging processes are investigated using thermodynamic analysis. The results indicate that increasing the solar irradiation by 36%, leads to 13% increase in the exergy efficiency of the cycle. Moreover, the mass flow rate of the heat transfer fluid in solar system has a considerable effect on the exergy cost of output power. Solar tower has the highest exergy destruction and capital investment cost. The highest exergoeconomic factor for the integrated cycle is 60.94%. The steam turbine and PEM electrolyser have the highest share of exergoeconomic factor i.e., 80.4% and 50%, respectively.     

Diluted chemical bath deposition of CdZnS as prospective buffer layer in CIGS solar cell

In this study, dilute chemical bath deposition technique has been used to deposit CdZnS thin films on soda-lime glass substrates. The structural, morphological, optoelectronic properties of as-grown films have been investigated as a function of different Zn²⁺ precursor concentrations. The X-ray diffractogram of CdS thin-film reveals a peak corresponding to (002) plane with wurtzite structure, and the peak shift has been observed with the increase of the Zn²⁺ concentration upon formation of CdZnS thin film. From morphological studies, it has been revealed that the diluted chemical bath deposition technique provides homogeneous distribution of film on the substrate even at a lower concentration of Zn²⁺. Optical characterization has shown that the transparency of the film is influenced by Zn²⁺ concentration and when the Zn²⁺ concentration is varied from 0 M to 0.0256 M, bandgap values of resulting films range from 2.42 eV to 3.90 eV while. Furthermore, electrical properties have shown that with increasing zinc concentration the resistivity of the film increases. Finally, numerical simulation validates and suggests that CdZnS buffer layer with composition of 0.0032 M Zn²⁺ concentration would be a promising candidate in CIGS solar cell.     

Effect mechanism of multiple obstacles on non-Newtonian flow in ceramics 3D printing (linear elements)

Direct ink writing (DIW) provides a new way to mould ceramic parts. When a single screw extruder is used to extrude SiC slurry, the deposits caused by low viscosity and the agglomerations resulting from the nonuniform mixing, form the obstacles in the channel, which affect the normal flow of the slurry, theoretical outlet velocity, and interaction with other printing parameters. Therefore, it is necessary to study the mechanism responsible for the effects of the obstacles on the flow. The obstacles are always irregular, which makes it difficult to directly analyse them. Irregular geometries are always composed of linear and/or arcuate elements; therefore, the obstacles can be simplified into regular geometries. In the present work, linear elements are analysed first. Then, an improved MRT LBM (multiple relaxation time lattice Boltzmann method) with a pseudo external force is proposed for the flow analysis. The improved MRT LBM is combined with rheological test data to investigate cases with two obstacles, and the results are applied to reveal the general mechanism in cases with multiple obstacles. The results show that the angles, sizes, and positions of the obstacles are three important factors influencing the flow. To obtain a stable and controllable slurry flow, it is recommended that the first angle θ₁ be an acute angle. In addition, the number of obstacles should be minimized, and the position of the last obstacle should be far away from the outlet.     

Effect of MoS2/PTFE coatings on performance of Si3N4/TiC ceramics in dry sliding against WC/Co

To enhance the tribological performance of Si₃N₄/TiC ceramics, MoS₂/PTFE composite coatings were deposited on the ceramic substrate through spraying method. The micrographs and basic properties of the MoS₂/PTFE coated samples were investigated. Dry sliding friction experiments against WC/Co ball were performed with the coated ceramics and traditional ones. These results showed that the composite coatings could significantly reduce the friction coefficient of ceramics, and protect the substrate from adhesion wear. The primary tribological mechanisms of the coated ceramics were abrasive wear, coating spalling and delamination, and the tribological property was transited from slight wear to serious wear with the increase of load because of the lower surface hardness and shear strength. The possible mechanisms for the effects of MoS₂/PTFE composite coatings on the friction performance of ceramics were discussed.